Immersion RC Tramp Nano 5.8GHz Video Transmitter
Only 18x13mm, and weighing in at a paltry 1.01g, the Tramp Nano packs quite a punch. Given adequate airflow, output powers of > 500mW (typically 700mW+) are emitted.
The Nano operates from the 5V regulated supply that most flight controllers supply these days, and doesn’t require a dedicated connection to the flight battery.
Features:
- Smallest 500mW+ vTx in the business.
-
Locking U.FL to SMA cable included
- 20 x 20mm Carrier PCB, with Gummies Supplied
-
1mW -> 500mW+ linear power control
-
Built-in thermal protection (second-gen)
- Factory power normalization
- Glitch-Free frequency changes
- Micro-power pit mode, with built-in ‘pit switch’
Locking U.FL Connector
The Tramp Nano, with it’s supplied U.FL to SMA cable, supports a locking U.FL connector that locks the connector onto the board without the need for screws, or tools.
20 x 20mm Carrier PCB + Gummies
Included with every Tramp Nano is a lightweight 20 x 20mm carrier PCB, with IRC gummies, suitable for M3 screws.
RGB Status LED
Green LED? all is well, transmitting normally.
Flashing Green LED? Pit Mode.
Flashing Blue LED? Race Locked, Tx not active.
Flashing Magenta LED? Race Locked, Tx transmitting.
Thermally Protected
Most video transmitters (even the higher end units) have no thermal protection whatsoever and will happily cook themselves and prematurely fail.
The Tramp is different as it constantly monitors its temperature, and gracefully reduces power output to increase battery life and protect itself. Once props start spinning, power gets boosted.
Touch ‘n’ Race for Race Directors
Race directors can, without powering up a model, define the frequency and power output of the transmitter, in 5 seconds flat before a race starts.
Touch ‘n’ Race for Pilots
Touch-free programming of video transmitters before you launch, eliminating frequency collisions, eliminating the ‘what channel was I on last’ question, and allowing power levels to be modified between flights to adapt to local conditions.
Calibrated Power
Every member of the Tramp family ever shipped has been factory calibrated to ensure precise power outputs, especially at the critical low-power race levels.
Specifications:
-
Dimensions: L=18mm x W=13mm x H = 3.2mm
- Weight: 1.01g (Tx only, without SMA cable)
- Power Output: Programmable, 1mW to > 500mW 1
- Channels: 48 standard, arbitrary using race wand
- RF Impedance: 50 ohms
- RF Connector: U.FL (with Locking Pigtail)
- AV Connector: Solder Pads
- TNR Connector: Solder Pads
- Audio: None
-
Video Impedance: 75 ohms
- Power Requirements: 5V DC (operates down to ~3.5V, but 5V recommended)
Includes:
1x Immersion RC Tramp Nano 5.8GHz VTX
1x 20 x 20mm Carrier PCB
4x Anti-Vibration Gummies
1x u.FL to SMA connector
1x Wire Set
|
REGULATORY NOTICE The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. Defiance RC, Inc cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice. |
